Communications Electronics, Inc. and Watkins-Johnson Equipment Guide 3/01/96 This is an ongoing project. I'm always looking for more information, particularly on the variants denoted by the -x suffixes. Copyright 1995 by Terry O'Laughlin. All units are rack mount 3.5" high unless noted. Receivers: Model Coverage Bandwidths Notes -------- ----------- ----------------- -------------------------- 112 1-18gHz 100kHz/2/4/10/ receiver, AM/FM/pulse, TH-series 20mHz filmstrip dial, AFC, DAFC, drop-in "aural enhancement", dual tuners conversion, IFs: 160 & 21.4mHz, center tune and signal strength meters, solid-state, 23lbs 112-1 1-18gHz 100/500kHz/1/ same as 112 except for BW 10/20mHz 112R 1-18gHz EMC version of 112 205 2-1000mHz 10/50/300khz/ Pan-Man receiver, filmstrip HH-, VH- 1mHz dials, AM/FM/pulse, scans or UH- pan (full band) or sector series (adjustable width centered tuners on tuner frequency), center tune and signal strength meters, 21.4mHz IF, solid- state, 19lbs 205-2 similar to 205 except with additional scan mode of pan/sector (alternates traces), and remote tune 215 similar to 205-2 except w/ TTL digital remote interface 232-1 2-32mHz 6kHz tunable filter, basically a triple conversion rcvr w/o demod, IFs=65mHz/10mHz and 15kHz, 6kHz BW filter, COR, DAFC input (from DRO-307-1), 1/2 rack width 232-2 2-32mHz 6kHz same as 232-1 except with 25kHz final IF 301A 3-30kHz 200Hz round dial, AM/CW, three band 3-6/6-14/14-30kHz, 45kHz IF, AGC, solid-state, 14lbs, cost $1000 (1967) 301A-1 3-30kHz 200Hz same as 301A but w/optional internal rechargeable batt, cost $1200 (1967) 302 30-300kHz 2kHz round dial, AM/CW, three band 30-60/60-140/140-300 kHz, 455kHz IF, AGC, solid- state, 13.5lbs, cost $1000 (1967) 340A 1-900kHz 1/6/20/50kHz 5 digit LED counter, AM/FM/ CW, DAFC, ant attn, 50/600 ohm ant, remote control, solid-state 340A-7 1-900kHz 1/6/20/50kHz diff unknown 340A-8 1-900kHz 0.3/1/3/20/50kHz same as 340A except for different IF bandwidths 351 1-600kHz 0.15/1/3/6kHz 4 digit Nixie counter, decimal shift, DAFC, AM/ SSB/CW/FSK,BFO w/zero/ variable/1kHz/USB/LSB, ant attn, audio BW filters, solid-state, 20lbs, cost $4000 (1967) 351-1 1-600kHz 1/6/20/50kHz AM/FM/USB/LSB/CW/Pulse, filmstrip dial, solid- state, ant. atten., BFO w/var/5.5kHz/USB/LSB 354 1-600kHz 0.15/1/3/6kHz filmstrip dial, AM/SSB/CW/ FSK, BFO w/zero/variable/ 5.5kHz/USB/LSB, ant attn, audio BW filters, solid- state, 20lbs, cost $2500 (1967) 355 1-600kHz 1/6/20/50kHz filmstrip dial, AM/SSB/CW/ FSK, BFO w/zero/variable/ 5.5kHz/USB/LSB, ant attn, audio BW filter, solid- state, 20lbs, cost $3000 (1967) 355-1 1-600kHz 1/6/20/50kHz same as 355 w/addition of X-Y outputs to driver plotter, cost $3200 (1967) 355-2 1-600kHz 1/6/20/50kHz same as 355 w/addition of internal rechargeable batteries, cost $3700 (1967) 357 1-600kHz 0.15/1/3/6kHz 4 digit Nixie counter, decimal shift, DAFC, AM/ SSB/CW/FSK, BFO w/zero/ variable/5.5kHz/USB/LSB, noise limiter, audio BW filter, 2mHz IF, solid- state, (have manual) (mil versions: R-1401 and R-1490A/G), 20lbs, cost $4200 (1967) 371A 0.5-10mHz 6/20/100/400kHz AM/FM/CW, filmstrip dial, dual conversion on 6&20kHz IF BWs (21.4mHz & 455kHz), LO out, SM out (21.4mHz), designed for RFI detection, solid-state, 25lbs, cost $3000 (1968) 372A 0.5-30mHz 6/20/100/400kHz AM/FM/CW, filmstrip dial, designed for RFI detection, solid-state 372A-2 0.5-30mHz 6/20/100/400kHz same as 372A except has X-Y outputs for recording spectral analysis 373A 0.5-30mHz 6/20/100/400kHz AM/FM/CW, filmstrip dial, dual tuner version of 371A, 25lbs, cost $3500 (1968) 373A-2 0.5-30mHz 6/20/100/400kHz same as 373A except has X-Y outputs for recording spectral analysis 377A 0.5-10mHz 6/20/100/400kHz AM/FM/CW, 6 digit Nixie counter display, DAFC, dual conversion on 6&20kHz IF BWs, SM output, solid- state, 25lbs, cost $4500 (1967) 402-1 20-40mHz 10kHz 1 chan xtal controlled, AM/CW, 21.4mHz IF, 1/5 rack width, 5.25" high, 4.5lbs, cost $995 (1965) 402-2 40-60mHz 10kHz same as 402-1 402-3 60-90mHz 10kHz same as 402-1 410 20-80mHz 10kHz plug-in receiver, AM/FM, activity operated relay (AOR), DAFC input, mounts in EF-158 as part of RS-158 410-2 20-80mHz 20kHz same as 410 410-3 20-80mHz 50mHz same as 410 415-1 60-90mHz 50kHz (100kHz 4 chan xtal controlled, - special order) AM only, 21.4mHz IF, 1/4 rack width, 3.75" wide, 6.75" high, 6.5lbs, cost $995 (1966) 415-2 75-110mHz 50kHz same as 415-1 415-3 90-130mHz 50kHz same as 415-1 415-4 110-150mHz 50kHz same as 415-1 416-1 30-90mHz 2mHz 4 chan xtal controlled, pulse only, other specs like 415 416-2 75-110mHz 2mHz 4 chan xtal controlled, pulse only, other specs like 415 416-3 90-130mHz 2mHz 4 chan xtal controlled, pulse only, other specs like 415 416-4 110-150mHz 2mHz 4 chan xtal controlled, pulse only, other specs like 415 416-6 30-90mHz unknown 4 chan xtal controlled, other specs unknown 416-12 60-260mHz unknown same as 416-6 440-1 30-48mHz 20/50/75 or 100 xtal control rcvr, AM only, kHz 1/6 rack width, second suffix denotes bandwidth -1 =50kHz, -2 =20kHz, -3 =75kHz -4 =100kHz 440-2 45-72mHz other specs same as 440-1 440-3 70-105mHz other specs same as 440-1 440-4 100-160mHz other specs same as 440-1 440-5 150-220mHz other specs same as 440-1 440-6 210-260mHz other specs same as 440-1 441-1 30-48mHz 20/50/75 or 100 xtal control rcvr, FM only, kHz 1/6 rack width, second suffix denotes bandwidth -1 =50kHz, -2 =20kHz, -3 =75kHz -4 =100kHz fit EF-506B rack 441-2 45-72mHz other specs same as 440-1 441-3 70-105mHz other specs same as 440-1 441-4 100-160mHz other specs same as 440-1 441-5 150-220mHz other specs same as 440-1 441-6 210-260mHz other specs same as 440-1 461-1 300-450mHz see descrip single xtal channel, AM/FM, BWs noted by 2nd suffix: -1 =50kHz, -2 =20kHz, -3 =75kHz -4 = 100kHz 1/6 rack width, fit EF-506 rack 461-2 450-550mHz same as 461-1 480 series these tuners are listed under components as they require the supply in the EF-180A or EF-182A rack 501 54-260mHz 10/300kHz round dial, AM/FM/CW, video BW filters, built-in speaker, center tune and signal strength meters, 21.4mHz IF, solid-state, nuvistors & 7077 501A 54-260mHz 10/300kHz filmstrip dial, AM/FM/CW, video BW filters, built-in speaker, center tune and signal strength meters, 21.4mHz IF, solid-state, 15lbs, cost $1600 (1967) 501A-1 54-260mHz 10/300kHz same as 501A except w/AFC 504A 54-260mHz 10/300kHz same as 501A w/addition of 1 & 5mHz marker generator, cost $1750 (1967) 519 20-70mHz 10/50/300kHz filmstrip dial, AM/FM/CW, squelch, built-in SDU, dual conversion, 10mHz & 455kHz IFs, DAFC input (for DRO-290A), solid-state, 18lbs, cost $3100 (1967) 521A 20-70mHz 4/10/50kHz filmstrip dial, AM/FM/CW, COR, built-in SDU, dual conversion, 10mHz & 455kHz IFs, DAFC input (for DRO-209A), solid-state, 18lbs, cost $3200 (1967) 521A-1 20-80mHz 4/10/50kHz other specs same as 521A 555 90-180mHz 10/20/50kHz other specs similar to 521A 555-1 90-180mHz 4/10/50kHz other specs similar to 521A 565 20-1000mHz 10/50/100kHz/ AM/FM/CW/pulse, built-in (VH- & UH- 3mHz SDU, DAFC input plug-in tuners) 565A 20-1000mHz opt w/ WJ-9930 same as 565 except uses modules drop-in IF/BW/demod units 595 220-440mHz 10/20/50kHz other specs similar to 521A 601A 54-260mHz 50/100kHz round dial, AM/CW, squelch, dual conversion, 21.4mHz & 2.5mHz IFs, two separate IF strips, 50 & 100kHz BWs avail. simultaneously, solid-state & nuvistor, 12lbs, (1964) 701 235-1000mHz 300kHz/2mHz round dials, AM/FM/CW, two tuners: 235-500/490- 1000mHz, COR, dual conv., 60mHz & 21.4mHz IFs, two separate IF strips, 300kHz & 2mHz BWs avail. simult., solid-state, nuvistor, 7077s & 7486, 21lbs 701A 235-1000mHz 300kHz/2mHz same as 701 except 7077s & 7486 replaced by nuvistors, cost $3000 (1965) 702 235-1000mHz 50/300kHz/2mHz same as 701 except w/50kHz bandwidth 702A 235-1000mHz 50/300kHz/2mHz same as 702 except 7077s & 7486 replaced by nuvistors, cost $3500 (1965) 770 235-1000mHz 100/500kHz/4mHz round dials, AM/FM/CW/ pulse, two tuners: 235-500/ 490-1000mHz, IFs: 60, 21.4mHz (all BWs), 2.5mHz (100kHz only), nuvistors, several 7077s & 7486, solid-state (have manual) 770A 235-1000mHz 100/500kHz/4mHz same as 770 except 7077s and 7486 replaced by nuvistors 775 235-1000mHz 100/500kHz/4mHz same as 770A except w/COR (have manual) 775-3 235-1000mHz 100/500kHz/4mHz same as 775 except w/115/ 230VAC supply, cost $3700 (1967) (have manual) 775-9 235-1000mHz 100/500kHz/4mHz difference unknown 901B 30-300mHz 20/300kHz filmstrip dials, AM/FM/CW, two tuners: 30-90/60-300 mHz, nuvistor and solid- state, 18lbs, cost $1925 (1966) 901-5 30-300mHz 20/30/300kHz same specs as 905A except for additional IF BW 903B 30-300mHz 50/300kHz round dial, AM/FM/CW, ANL, COR, two tuners: 30-60/60- 300mHz, 21.4mHz IF, nuvistors (8058, 7587 & 6CW4) & solid-state, 20lbs, cost $2400 (have partial schematic) 904A 30-300mHz 20/300kHz same as 901B except with 1mHz & 5mHz xtal marker osc, cost $2075 (1966) 905A 30-300mHz 20/300kHz same as 901B except with COR, cost $2025 (1966) (mil R-1420/URR) (Fair has manual) 906A 30-300mHz 20/300kHz same as 901B except with 1mHz & 5mHz xtal marker osc and COR, cost $2175 (1966) (have manual) 906A-4 30-300mHz 20/300kHz same as 906A except with narrow band FM demod 907 30-300mHz 20/300kHz round dial, AM/FM/CW, two tuners: 30-100/60-300 mHz, special DC outputs from detectors, 21.4mHz IF, nuvistor & solid-state, 15lbs, cost $1975 (1965) 952 30-300mHz 50/300kHz filmstrip dial, AM/FM/CW, two tuners: 30-90/60-300 mHz or six xtal controlled chan between 100-150mHz, COR, 21.4mHz IF, 18lbs, cost $2400 (1967) 960 30-300mHz 20/200kHz round dials, AM/FM/CW, two tuners: 30-90/60-300 mHz, 21.4mHz IF, nuvistors, 7077 & solid-state, 16lbs 960B 30-300mHz 20/200kHz same as 960 except 7077s replaced by nuvistors, cost $2550 (1966) 960B-2 30-300mHz 20/300kHz same as 906B except with wider IF BW 965 10-90mHz 10/50/200kHz round dials, AM/FM/CW, two tuners: 30-90/10-30mHz, 21.4mHz IF, 17lbs, cost $2900 970A 30-300mHz 60/300kHz/3mHz round dials, FM/AM/CW/ pulse, special AGC for pulse, dual conversion (60kHz BW only) 21.4mHz & 2.5mHz IFs, cost $2700 (1965) 975 30-300mHz 60/300kHz/3mHz same as 970A except with COR, cost $2800 (1965) 975-2 30-300mHz 60/300kHz/3mHz newer version of 975, cost $2700 (1967) 977 30-300mHz 60/300khz/3mHz filmstrip dials, AM/FM/CW/ pulse, solid-state, DAFC w/DRO-300A or DRO-302A-2, cost $2700 (1968) 977-1 30-300mHz 10/300kHz/3mHz other specs same as 977 CT-4080 4-8gHz 8mHz minimum tuner, one 160mHz output, two 21.4mHz output, 18dB max noise figure, AGC & DAFC inputs, 25lbs, used in RS-125, cost $6250 (1968) CV-1750 235-1000mHz 2mHz minimum military version of FE-25-1 FE-1-2A 0.95-2.05gHz 8mHz minimum converter, filmstrip dial, 160mHz IF out, 18dB max noise figure, four section YIG preselector, LO out, 20lbs, cost $4000 (1965) FE-1-2B 0.99-2.0gHz 8mHz minimum same as FE-1-2A except DAFC in, AGC in, slightly wider frequency range, 25lbs, cost $4000 (1967) FE-1-4.5 0.95-4.5gHz 8mHz minimum converter, consists of the tuner sections of FE-1-2B and FE-2-4.5 in one box, cost $8500 (1967) FE-2-4 2.0-4.0gHz 8mHz minimum converter, round dial, 160mHz IF out, 18dB max noise figure, tunable YIG preselector, AGC in, rack mount 5.25" high, 20lbs, cost $4000 (1965) FE-2-4.5 1.95-4.5gHz 8mHz minimum same specs as FE-1-2B except freq coverage FE-4-8 4-8gHz 8mHz minimum converter, filmstrip dial, 160mHz IF out, 18dB max noise figure, four section YIG preselector, DAFC in, AGC in, LO out, 25lbs, cost $6500 (1967) FE-8-12 8-12gHz 8mHz minimum converter, filmstrip dial, 160mHz IF out, 18dB max noise figure, four section YIG preselector, DAFC in, AGC in, LO out, 25lbs, cost $6500 (1967) FE-25-1 235-1000mHz 2mHz minimum converter, round dials, two tuners: 235-500/490- 1000mHz, 60 mHz IF out, 10 dB noise figure, 7077s, 7486 & nuvistors, 18lbs, cost $1400 (1967) (mil version: CV-1750) FE-26 235-1000mHz other specs unknown FE-103 10-30mHz 2mHz minimum converter, 60 mHz IF out, filmstrip dial, 6dB max noise figure, solid-state, 12lbs, cost $1000 (1965) (mil version available, number unknown) FE-3442 3.7-4.2gHz 20mHz converter, 160mHz IF out, 20mHz BW, 15dB noise figure compnent of TDS-100 system HF-1000 0.005-30mHz 58 digital AM/FM/CW/USB/LSB/ISB/ filters synchronous AM, fully synthesized, green LED digital readouts, 3 scanning modes, notch filter, bandpass tuning, RS-232 or CSMA remote control, rack mount 5.5" high, 97-253VAC, 47-440Hz, current issue commercial version of WJ-8711 HT-10 0.5-10mHz 400kHz converter, 21.4mHz out, 7dB noise figure, input attn, 15lbs, cost $2000 (1967) used in RS-125 LT-1-2 1.0-2.0gHz 8mHz minimum converter, round dial, 21.4mHz IF out, 18dB max noise figure, four section YIG preselector, solid- state except for ceramic triode LO, rack mount 5.25" high, 20lbs, cost $4500 (1965) LT-1020A 0.95-2.05gHz 8mHz minimum converter, 21.4mHz out, filmstrip dial, 18dB max noise figure, four section YIG preselector, dual conversion, 160mHz and 21.4mHz IFs, DAFC in, AGC in, 25lbs, cost $4200 (1967) MT-112 1-18gHz* microwave tuner frame, uses up to four TH- series tuning heads, 160mHz IF out, rack mount 5.25" high R-1279 30-300mHz 20/300kHz round dials, nuvistor & solid-state (mil) R-1401 military version of 357 R-1420 military version of 905A R-1490A/G military version of 357 RS-111-1B 30-1000mHz 20/75/300kHz/ round dials, AM/FM/CW, 2mHz four tuners: 30-60/60-300/ 235-500/490-1000mHz, built-in SDU, separate 2mHz IF w/AM and FM continuously available, seperate antenna inputs for VHF and UHF, nuvistors, 7077s, 7486 and solid-state, rack mount 5.25" high, 35lbs, cost $6250 (1967) (have manual) (mil URR-52B) RS-111-1B-7 30-1000mHz 20/75/300kHz/ same specs as RS-111-1B 2mHz except has single antenna input switched to all tuners internally and video output switched between AM & FM by front panel mode control, cost $6250 (1968) RS-111-1B-12 30-1000mHz 20/75/300kHz same specs as RS-111-1B /2mHz except contains a 21.4mHz marker oscillator for SDU cost $6250 (1968) RS-111-1B-12B 30-1000mHz 20/75/300kHz same specs as RS-111-1B /2mHz except contains a 21.4mHz marker oscillator for SDU and DAFC input, cost $6250 (1969) S302 30-300kHz 2kHz scanning version of 302 SCT-4080 4-8gHz 8mHz minimum scanning version of CT-4080, 30lbs, cost $7250 (1968) SHT-10 0.5-10mHz scanning version of HT-10 SLT-1-2 1.0-2.0gHz 8mHz minimum scanning version of LT-1-2, 23lbs, cost $5000 (1965) specs unknown SLT-1020A 0.95-2.05gHz 8mHz minimum same as LT-1020A except w/ motorized automatic tuning, 30lbs, cost $5600 (1967) SST-1045 0.95-4.5gHz 8mHz minimum same as ST-1045 except w/ motorized automatic tuning, 30lbs, cost $10500 (1967) ST-1045 0.95-4.5gHz 8mHz minimum converter, 21.4mHz out, filmstrip dials, two tuners: 0.95-2.05/1.95-4.5 gHz, 18dB max noise figure, four section YIG tuned preselector, dual conversion, 160mHz & 21.4mHz IFs, AGC in, DAFC in, 25lbs, cost $8700 (1967) SST-2045 1.95-4.5mHz 8mHz minimum sames specs as ST-2045 except with motorized automatic tuning, 30lbs, cost $5600 (1967) ST-2045 1.95-4.5gHz 8mHz minimum same specs as ST-1045 except with one tuner, cost $4200 (1967) SUT-1000 235-1000mHz 6mHz minimum same specs as UT-1000 except with motorized automatic tuning, 25lbs, cost $3250 (1967) SVT-10 10-90mHz 2mHz minimum same specs as VT-10 except with motorized automatic tuning, 22lbs, cost $2550 (1967) SVT-11 10-30mHz 2mHz minimum same specs as VT-11 except with motorized automatic tuning, 20lbs, cost $1500 (1967) SVT-30 30-260mHz 3mHz minimum same specs as VT-30 except with motorized automatic tuning, 21.5lbs, cost $2750 (1967) SXT-8012 8-12mHz scanning version of XT-8012 URR-52B military version of RS-111 URR-74 military version of WJ-8718 UT-1000 235-1000mHz 6mHz minimum converter, 21.4 mHz out, round dials, two tuners: 235-500/490-1000mHz, 14dB max noise figure, LO out, AGC in, 18.5lbs, cost $2500 (1967) VT-10 10-90mHz 2mHz minimum converter, 21.4mHz out, filmstrip dials, two tuners: 10-30/30-90mHz, 7dB max noise figure, 16lbs, cost $1800 (1967) VT-11 10-30mHz 2mHz minimum same specs as VT-10 except single tuner, 15lbs, cost $1000, (1967) VT-30 30-260mHz 3mHz minimum converter, 21.4 mHz out, round dials, two tuners; 30-60/54-260mHz, 6.5dB max noise figure, LO out, AGC in, 7077s & nuvistors, 15lbs, cost $2000 (1967) WJ-1033-1 500-100mHz 20mHz tuner, 160mHz IF output, 18dB noise figure WJ-1034 1-2gHz 30mHz tuner, 160mHz IF output, 15dB noise figure WJ-1035 2-4gHz 30mHz tuner, 160mHz IF, 15db NF WJ-1036 4-8gHz 35mHz tuner, 160mHz IF, 20db NF WJ-1037 8-12gHz 25mHz tuner, 160mHz IF, 20db NF WJ-1038 12-18gHz 30mHz tuner, 160mHz IF, 20db NF WJ-1091 30-50mHz 300kHz tuner, 21.4mHz IF output, 6dB noise figure WJ-1092 50-100mHz 300kHz tuner, 21.4mHz IF, 7dB NF WJ-1093 100-170mHz 300kHz tuner, 21.4mHz IF, 7.5dB NF WJ-1094 170-250mHz 300kHz tuner, 21.4mHz IF, 9dB NF WJ-1095 250-500mHz 300kHz tuner, 21.4mHz IF, 10dB NF WJ-1096 500-1000mHz 300kHz tuner, 60mHz IF, 12dB NF WJ-8604 20-512mHz same specs as WJ-8607 except smaller package and quick disconnect connector WJ-8607 20-512mHz 10/20/50/250kHz/ miniceptor, AM/FM/CW/Pulse 4mHz standard (SSB opt), microprocessor (6.4kHz-8mHz control, 100Hz resolution, available) HPIL/RS-232 remote interface, scan, step, can be used with WJ-9902 and WJ-9908 equip frames or WJ-9605 and WJ-9607 front panels, 1.5"h x 6.5"w x 10.5d, 5lbs WJ-8607fe 2-2000mHz same specs as WJ-8607 WJ-8609A 20-512mHz 0.25-40mHz avail same specs as WJ-8607 except AM/FM/Pulse only WJ-8609A-1 0.235-18gHz 5 from 0.25- wideband version of 40mHz (SAW fils) WJ-8609A, uses WJ-9290 block downconverter, AM/FM/ Pulse, RF preselection, 100Hz resolution, scan, step, remote control: HPIL, RS-232 or RS-422 WJ-8615D 20-500mHz 10/20/50/100/ AM/FM/CW/USB/LSB/pulse, 300kHz synthesized, micropro- cessor controlled w/100Hz steps, LED readout, COR, IEEE-488 interface, 1/2 rack width 3.25"h, opts: coverage to 4.5gHz, IF BWs from 3.2kHz to 4mHz WJ-8615P 20-500mHz 3 std from 3.2kHz AM/FM/CW/Pulse, SSB opt, -8mHz (5 as opt) microprocessor control, step, scan, lockout, clock, calendar, integral battery backup, logs signal acquisition w/ date & time to RS-232, printer or audio interface, options include tracking preselector, selected audio, wideband outputs, 3.5"h x 8.25"w x 20"d, 25lbs WJ-8616 20-500mHz synthesized, 7 digit LED readout WJ-8617B 20-500mHz 10/20/100/500khz AM/FM/CW/SSB/pulse, (0.5-1100 2mHz synthesized, micropro- mHz opt, cessor controlled w/100Hz down to steps, 7 digit LED readout, 10kHz on 48 programmable search special bands, 96 memory channels, request) search/scan for user-defined processing or signal acquisition, built-in SDU, master/slave operation of up to 29 receivers, rack mount 5.25" high, 50 lbs WJ-8619 20-500mHz 5 BWs, 11 avail AM/FM/CW/Pulse std, SSB from 10kHz-4mHz & var BFO opt, digital remote controlled by IEEE-488 bus or WJ8617B receiver, 100Hz steps, COR, scan module w/X-Y-Z display out WJ-8619fe 20-1100mHz as above same as WJ-8619 except for expanded frequency range WJ-8625-1 0.2-1.5mHz AM/FM/CW/USB/LSB, LCD display WJ-8626A-1 same as A-4 but no front panel, controlled from A-4 WJ-8626A-4 5kHz-30mHz any 3 from 0.2/ AM/FM/CW/USB/LSB, 0.5/1/2/3/4/6/8/ synthesized, micropro- 12/16kHz cessor controlled, LCD display, 1/2 rack width 5.25" high WJ-8628A-1 same as A-4 but no front panel, controlled from A-4 WJ-8628A-4 20-512mHz four from range AM/FM/CW/SSB/pulse, of 10khz to 4mHz synthesized, micropro- cessor controlled w/100Hz steps, LCD display, tuned preselection, synth. BFO, 10mS tuning speed, opt: coverage to 1.4gHz, 1/2 rack width 5.25" high WJ-8640-1 plug-in 10/50/200kHz AM/FM/CW/USB/LSB, port- 0.5-500mHz 5/20kHz optional able manpack, LED counter w/DAFC, 10 D cell or BA- 4386 detachable battery pack or vehicular supply, 4.2"h X 11.4"w X 11.7"d, 18lbs, (mil AN/GRR-8V) WJ-8650 105-175mHz 5/15kHz minature receiver, AM/FM, 10 chan, scan, step, tracking preselector, 10-14VDC, 4W, 4.25"dia x 0.6"high, 10oz WJ-8650-1 200-270mHz 15kHz same specs as WJ-8650 except 0.8" high WJ-8652 210-350mHz 100kHz/1/2mHz minature receiver, AM/FM, 5 chan, scan, step, tracking preselector, 10-14VDC, 2.5W, 0.75"h x 3.25"w x 7.12"d, 1lb WJ-8653A 400-500mHz 25kHz minature receiver, FM, or 0.8-1.0gHz scan, step, 10-14VDC, 5W, 0.8"h x 3.5"w x 8.75"d, 1lb WJ-8654 20-1000mHz 6.4-100kHz miniceptor, AM/FM/SSB/CW, 100 chan, scan, step, tracking preselector, HPIL &RS-232 remote interface, 9-16VDC, 5W, 1.65"h x 3.0"w x 7.75" d, 2.5lbs WJ-8700 0.5-32mHz dual receiver, AM/FM/CW/ USB/LSB, microprocessor control, 8 line by 40 char LCD display, scan, step, lockout, 100 memory channels, suboctave pre- selector, many options, 3.5"h x 8.25"w x 20"d, 18lbs WJ-8709 5kHz-30mHz 0.3/1/3.2/6/16kHz AM/FM/CW/MCW/USB/LSB, 7 digit yellow LED display, synthesized: 10Hz steps, 1/2 rack width 5.25" h WJ-8711 0.005-30mHz 58 digital AM/FM/CW/USB/LSB/ISB/ filters synchronous AM, fully synthesized, green LED digital readouts, 3 scanning modes, notch filter, bandpass tuning, RS-232 or CSMA remote control, rack mount 5.5" high, 97-253VAC, 47-440Hz, current issue, WJ-8712 5kHz-30mHz 58 digital remote control version of filters WJ-8711, half rack 3.5" high, blank front panel, RS-232 or CSMA control WJ-8718A 5kHz-30mHz 0.3/1/3.2/6/16kHz AM/FM/CW/ISB/USB/LSB, synthesized, micropro- cessor controlled w/10Hz steps, 7 digit LED readout (yellow), synthesized BFO, many options notably including /MFP - micropro- cessor front panel which allows front panel control of scanning and memory, rack mount 5.25" high, 35lbs WJ-8721 5kHz-30mHz digital VXI card version of WJ-8711, 1/12 rack width, BITE, 5lbs WJ-8730A plug-in plug-in uses two WJ9060 tuning 20-1000mHz 10kHz-3mHz heads (filmstrip dial), (WJ-9060 (WJ-9930 solid-state, built-in series) series) SDU WJ-8731A same specs as WJ8730A except with tuning meter instead of SDU WJ-8732A same specs as WJ8730A except only one WJ9060 tuning head WJ-8733A same specs as WJ8730A except only one WJ9060 tuning head and tuning meter instead of SDU WJ-8770 5kHz-20mHz 1/4/8/16kHz std, AM/FM/CW/LSB/USB, synth- 0.5/2/6/12kHz opt esized: 10Hz steps, red LED display, ruggidized, military vehicular radio 22-32VDC, internal AC or battery packs opt WJ-8809 0.1-18.5gHz 5 from 0.5-40mHz consists of two units, WJ-8809/RX receiver and WJ-8809/MC microwave converter, AM/FM/Pulse, 100Hz resolution, RF preselection, WJ-8880 0.5-30mHz six, opt config AM/FM/CW/USB/LSB/ISB, synthesized, micropro- cessor control, rack mount 5.25" high WJ-8888A 0.5-30mHz six, opt config AM/FM/CW/ISB/LSB/USB, synthesized, 10Hz steps, digitally remote control- able, rack mount 5.25" high WJ-8888B 0.5-30mHz six, opt config same as WJ-8888A except improved circuit board design WJ-8922 1kHz-3gHz AM/FM/CW/SSB, scans pan/ sector or manual, compact unit fits in a suitcase WJ-8969 0.5-18gHz 70mHz IF, synthesized, 1kHz steps WJ-8972 20-500mHz receiver/DF controller, part of WJ8990 system WJ-9080 30-1000mHz n/a converter, tunes all in one band XT-8012 8-12gHz 8mHz minimum converter, one 160mHz IF output, two 21.4mHz outputs, 18dB max noise figure, four section YIG preselector, DAFC in, AGC in, LO out, 25lbs, cost $6500 (1968) Spectrum Display Units (SDU): Model IF Bandwidths Notes -------- ---------- ---------------- --------------------------- 605 21.4 mHz variable solid-state, 1"x3" CRT IP-751 military version of SM-9310A IP-1355 10mHz 0-1mHz military version of WJ-9180-1 PD-102 remote SDU for RS-112 microwave Pan-Man receiving system PD-201 remote SDU same as PD-102 except 1/2 rack width PD-602 160mHz 1mHz solid-state, 8cm x 10cm CRT, component of RS-112, half rack 5.25" high, mount in EF-602 SM-1622 160 mHz 20mHz max nuvistors or solid-state, 1"x3" CRT, 200kHz resolution, 1/2 rack width SM-1622-1 160mHz 20mHz max same as SM-1622 except with 1mHz resolution SM-1662 160mHz 20mHz solid-state, 1"x3" CRT, 250kHz resolution, half rack width 3.5" high, 11lbs SM-1662-1 160mHz 20mHz same as SM-1662 except with 1mHz resolution SM-4300 21.4mHz 3mHz solid-state, 1"x3" CRT, 21.4mHz marker, 1/3 rack width, 5" high SM-4301A 21.4mHz 3mHz solid-state, 1"x3" CRT, 21.4mHz marker, 1/4 rack width, 6.75" high, 7.5lbs, cost $850 (1967) SM-7301 21.4mHz 30/100/500kHz/ solid-state, 8cm x 10cm CRT, 3mHz linear/log, part of RS-160 receiving system, full rack width 5.25" high, SM-7301 occupies half of rack w/ provisions for DRO-308 in the other half SM-8421 2mHz 3/15/50kHz solid-state, 1" x 3" CRT, marker generator, sweep disable, H&V outputs, (internally converts 2mHz to 455mHz), for use with VLF receivers like the 354, 355 and 357, 12lbs, cost $2500 (1968) SM-8510 500kHz 5/20/50kHz nuvistors & solid-state, 1"x3" CRT, lin/log display, 15lbs, cost $1400 (1967) mod kit for pairing w/ Collins 51J-4 or 51S-1 was included SM-8511 500kHz 5/20/50/200kHz same specs as SM-8510 except wider sweep width, cost $1600 (1967) SM-8512 455kHz 5/20/50kHz same specs as SM-8510 except for IF input freq, cost $1400 (1967) mod kit for pairing with R-390 or R-390A was included SM-8513 455kHz 5/20/50kHz two SM-8512 units in 5.25" high side by side rack mount, cost $2900 (1967) SM-9188 455kHz 5/15/30 kHz for use with 8718 series SM-9205 21.4mHz variable to 5mHz SDU for use w/up to three receivers, displays three traces simultaneously, digitally refreshed LCD display, common adjustments like sweep rate and centering are automatic, all three traces can be adjusted independently via manual or IEEE-488 remote control, 1/2 rack width 3.5" high. SM-9206 21.4mHz 0.1/0.2/0.4/1/2/ simplified 9205, single 5mHz trace, 3 selectable inputs, CRT display, 1/2 rack width 3.5" high. SM-9301 21.4mHz 3mHz solid-state, 1"x3" CRT, 21.4mHz marker, 8lbs, cost $850 (1967) SM-9302 21.4mHz 3mHz half rack version of SM-9301, 7lbs, cost $800 (1967) SM-9303A 21.4mHz 3mHz solid-state, 1"x3" CRT, input bandpass filtering, MOS FET first mixer, 21.4mHz marker, 11lbs, cost $1000 (1967) SM-9304A 21.4mHz 3mHz half rack version of SM-9303, 10lbs, cost $950 (1967) SM-9310A 21.4 mHz variable nuvistors, 1"x3" CRT (mil IP-751) SM-9401B 21.4mHz 4mHz solid-state, 1"x3" CRT, 21.4mHz marker, 8lbs SM-9402A 21.4mHz 4mHz half rack version of SM-9401B, 7lbs SM-9403A 21.4mHz 4mHz same specs as SM-9303A except wider sweep width SM-9404A 21.4mHz 4mHz half rack version of SM-9403A SM-9801 21.4mHz 8mHz same specs as SM-9301, cost $950 (1967) SM-9802A 21.4mHz 8mHz half rack version of SM-9801A, cost $900 (1967) SM-9803A 21.4mHz 8mHz same specs as SM-9303A except wider sweep width SM-9804A 21.4mHz 8mHz half rack version of SM-9803A SM-9805A 21.4mHz 8mHz solid-state, 2.625" x 4.625" CRT, avail with P1 or P7 phosphor SM-9831 30mHz 8mHz solid-state, 1"x3" CRT, 30mHz marker, 8lbs, cost $950 (1967) SM-9832 30mHz 8mHz half rack version of SM-9831 SPD-214 21.4mHz 3mHz max nuvistors, 1/2 rack width WJ-9180-1 10mHz 0-1mHz 5-25Hz sweep rate, 10uV input sensitivity, battery powered (10 D-cell or magnesium BA-4386 pack) or 24VDC vehicular supply, designed to accompany WJ8640-1 receiver (mil IP-1355/GRR-8V) WJ-9188A 455kHz 5/30kHz solid-state, 1'x3" CRT, marker, half rack width WJ-9188A-18 455kHz 5/15/30kHz 2.5" x 3" CRT, used with WJ-8888B or WJ-8718 w/ SMO option, full rack width WJ-9205 21.4mHz 5kHz-5mHz 4" CRT, displays 3 simultaneous traces, auto sweep and centering, IEEE-488 interface, 3.5"h x 8.5"w x 22"d, 18lbs WJ-9206 21.4mHz 0-5mHz 4" CRT, single trace, 3.5"h x 8.5"w x 22"d, 17lbs WJ-9207 RF panoramic display unit, digitally refreshed EL flat panel display, display 4 simultaneous scans, companion to WJ-8607 miniceptors (req WJ-8607/DSO option), 5.25"h x 8.75"w x 22"d, 13lbs WJ-9209 455kHz 5/15/30kHz combination SDU and speaker unit, 2.5" x 3" CRT, five input selector for speaker, half rack width 5.25" high Components and Accessories: Model Description -------- ---------------------------------------------------------- 481A plug-in receiver, 30-60mHz, AM/FM (CW opt), requires ext power from EF-180A or EF-182A equipment frame, component of RS-180 receiving system 482A same as 481A except 60-120mHz 483A same as 481A except 100-180mHz 484A same as 481A except 180-300mHz 485A same as 481A except 30-90mHz 486A same as 481A except 80-250mHz 487A same as 481A except 20-80mHz 488A same as 481A except 220-440mHz 489A same as 481A except 250-500mHz 490A same as 481A except 500-1000mHz AGC-BC Box car AGC unit, plugs into DM-4 AGC-PS Pulse stretching AGC, plugs into DM-4 ANT-101 antenna, 3.7-4.2gHz, 12dB gain, 25 degree beamwidth, component of TDS-100 system APR-101 antenna/preamplifier, ANT-101 and PR-101 in single unit AR7-15 antenna, log-periodic, 1-12.4gHz, 8dB gain, 15dB F-to-B AR7-17 antenna, log-periodic, 0.5-12.4gHz, 8dB gain, 15dB F-to-B AR12-18 antenna, log-periodic, 30-1100mHz, 8dB gain, 20dB F-to-B AR12-19 antenna, log-periodic, 90-1100mHz, 8dB gain, 20dB F-to-B AR12-20 antenna, log-periodic, 250-1100mHz, 8dB gain, 20dB F-to-B AR12-22 antenna, log-periodic, 30-160mHz, 8dB gain, 20dB F-to-B AR12-25 antenna, log-periodic, 30-76mHz, 8dB gain, 20dB F-to-B AR12-29 antenna, log-periodic, 30-300mHz, 8dB gain, 20dB F-to-B AR19-5 antenna, omnidirectional conical spiral, 1-11gHz, no gain, 5w power handling AR19-6 antenna, omnidirectional conical spiral, 7-11gHz, no gain, 5w power handling AR19-8 antenna, omnidirectional conical spiral, 150mHz-2gHz, no gain, 5w power handling AR19-9 antenna, omnidirectional conical spiral, 0.2-1.4gHz, no gain, 5w power handling AR19-10 antenna, omnidirectional conical spiral, 0.25-1.1gHz, no gain, 5w power handling AR19-11 antenna, omnidirectional conical spiral, 0.3-1.3gHz, no gain, 5w power handling AR23-4 antenna, loop, 2-30mHz, bi-directional figure eight AR72-4 antenna, loop, 30-160mHz, bi-directional figure eight AR122-1 antenna, compacted log-periodic, 150mHz-1gHz, 4.3dB gain, 10w power handling AR132-1 antenna, compacted log-periodic, 20-300mHz, 5dB gain, 1kw power handling AR272-1 antenna, dual polarization log-periodic, 1-4gHz, 8dB gain, 20dB F-to-B, 10w power handling AR274-1 antenna, dual polarization log-periodic, 30mHz-1gHz, 8dB gain, 20dB F-to-B, 25w power handling AR274-2 antenna, dual polarization log-periodic, 30-300mHz, 8dB gain, 20dB F-to-B, 25w power handling AR274-3 antenna, dual polarization log-periodic, 250mHz-1gHz, 8dB gain, 20dB F-to-B, 25w power handling CSU-160 tuner switching unit, works with 205, 205-2 or 215 Pan-Man receivers, manual or sequential scan of tuners, holds up to 7 tuners, part of RS-160, see RS-160 for details DA-1 video distribution amplifier, 91ohms or high impedance, 1.5vrms out, 6 video, 1 oscilloscope & 2 audio out, 9lbs, cost $1200 (1964) DA-5 audio distribution amplifier, 10kohm in, 150/600ohm out, 150Hz-10kHz response, five outputs, cost $595 (1966) DM-4 demodulator, 21.4mHz input, accepts 4 plug-ins, 6mHz bandwidth, BFO, squelch, tuning and signal strength meters, 3 audio outputs: 100mw into 600ohm, built-in speaker, 3 video outputs: analysis, recorder & tracking DM-22A demodulator, 21.4mHz input, AM only, BW=1.5mHz DM-112 demodulator, 160mHz input, 100kHz/2/4/10/20mHz BWs, AM/FM/ pulse, built in SDU, AFC and AGC outputs (to tuner), carrier and center-tune meters, typically paired with MT-112 DM-160 demodulator, 160mHz input, AM/FM/pulse, BW=0.35/1.5/4mHz DM-161 demodulator, 160mHz input, AM/FM/pulse, BW=1/5/10/20mHz DM-212 demodulator, 160mHz input, AM/FM/pulse, BW=10/20 mHz DM-235 demodulator, 160mHz input, BW=30/50 mHz DMS-105 tunable demodulator, 1-1600kHz, 5 digit Nixie readout, AM/FM/SSB/CW/MCW/FSK, IF BWs in two ranges: SSB - 2.4/ 3.5/4/8kHz; other modes - 0.15/1/5/7/8/16kHz, DAFC, rack mount 5.25" high DMS-105A same as DMS-105 except SSB BWs= 2.4/4/8kHz and has translated IF predetection outputs at 15/50/100kHz DMS-105R EMC version of DMS-105A, also has predetection IF outputs of 10/50/100kHz DMS-107 tunable demodulator, 0.1-10mHz, filmstrip dial, IF BWs: 20/50/100/300/500kHz/1/2/3mHz, DAFC w/DRO-302 or DRO-320, carrier and center tune meters DMS-107-1 same as DMS-107 except BW= 20/50/100/300/500kHz/1/3/5.5mHz DMS-109 tunable demodulator, 5kHz-1mHz, 5 digit Nixie display, USB/LSB, BW=2.8kHz, DAFC DMS-201 tunable demodulator, 0.5-10mHz, CW/FSK, BW=1/3kHz DRO-50 digital frequency display, 0.54-54mHz, for use with 455kHz IF receivers, 6 digit Nixie display, included kit for modifying SP-600, cost $2500 (1967) (variants were available for 500kHz, 3.9mHz and 21.4mHz IFs) DRO-270 digital frequncy display, 20-80mHz, for use with 10mHz IF receivers, 5 digit Nixie readout, DAFC for up to twelve receivers, part of RS-158 receiving system, rack mount 1.75" high DRO-280A digital frequency display, 20-1000mHz, 6 digit LED display, DAFC, provides control of 12 receivers in 15 msec intervals, 12 position switch for selecting receiver whose frequency is to displayed, part of RS-180 receiving system DRO-290 digital frequency display, 20-90mHz, for use with 10mHz IF receivers like CEI 519 and 521A, DAFC, 6 digit Nixie display, rack mount 1.75" high, 10lbs, cost $3100 (1967) DRO-290B similar to DRO-290 except with LED display DRO-300 digital frequency display, 30-300mHz, for use with 21.4mHz IF receivers, 6 digit Nixie display, variants avail for 455/500kHz and 3.9mHz IFs, cost $2800 (1967) DRO-302A digital frequency display, 30-300mHz, for use with 21.4mHz IF receivers, 6 digit Nixie display, DAFC output, 1/2 rack width, cost $3200 (1968) DRO-302A-2 digital frequency counter, same specs as DRO-302A except with BCD outputs DRO-302B digital frequency display, 0.1-500mHz, 6 digit LED readout, 21.4 & 60mHz IF presets (modifiable to any IF preset in increments of 0.1 mHz), solid-state, DAFC, half rack width (have manual) DRO-307 digital frequency display, 30-300mHz, 6 digit Nixie readout, 21.4mHz IF preset, DAFC control of four rcvrs w/ last two digits independently selectable for each rcvr, BCD outputs for all four receivers DRO-307-1 digital frequency display, 0.5-30mHz, 65mHz IF preset, otherwise similar to DRO-307 DRO-308 digital frequency display, 2-300mHz, 21.4mHz offset, 6 digit Nixie display, DAFC, component of RS-160 Pan-Man receiving system, mounts in SM-7301 frame 5.25" high DRO-309A digital frequency display, 0.1-1060mHz, same specs as DRO-302B (have manual) DRO-310 digital frequency display, 0.1-300mHz (4gHz w/plug-in mixers), 6 digit, 21.4mHz presets, multiple inputs, (mil CP-943/GLA-21), has accessory slot for mixers, SDU, ACL tuning heads. DRO-311 digital frequency display, 20-500mHz, automatic IF offset when used with 565 or WJ-8730 series, time-shares control of four receivers, drives up to four RD-105 remote displays DRO-312 digital frequency display, 0.01-1000mHz DRO-315 digital frequency display, 0.1-500mHz, identical to DRO-302B except full rack width, 1-3/4" high (have manual) DRO-333 digital frequency display, 0.1-1060mHz, identical to DRO-309A except full rack width, 1-3/4" high (have manual) DRO-333A same as DRO-333 except with ICs instead of discrete components in the counter section DRX-308 frequency extender for DRO-308, 300-1000mHz, rack mount 1.75" high DRX-1000 frequency extender for DRO-300 and DRO-302 counters, 235-1000mHz, also extends DAFC operation, half rack width DTF-101 test module for DM-4 demodulator, test DM-4 by plugging into any of the four module slots, cost $225 (1965) EC-101 extender cable for DM-4 module, allows for testing of IFD units outside of DM-4, cost $150 (1965) EF-101 equipment frame, single unit rack mount for 1/2 rack width units with front panels 3.25"h X 8.0"w EF-158 equipment frame for RS-158 receiving system, contains an RF multicoupler for 12 receivers w/ 50 ohm and 5dB max noise figure and an RF test signal generator EF-160 cabinet for RS-160 Pan-Man receiving system EF-201 equipment frame, dual unit rack mount for 1/2 rack width units with front panels 3.25"h X 8.0"w EF-301 equipment frame, single unit rack mount for 1/3 rack width units with front panels 5.0"h X 4.5"w EF-302 equipment frame, dual unit rack mount for 1/3 rack width units with front panels 5.0"h X 4.5"w EF-303 equipment frame, triple unit rack mount for 1/3 rack width units with front panels 5.0"h X 4.5"w EF-401 equipment frame, single unit rack mount for 1/4 rack width units with front panels 6.75"h X 3.75"w EF-402 equipment frame, dual unit rack mount for 1/4 rack width units with front panels 6.75"h X 3.75"w EF-403 equipment frame, triple unit rack mount for 1/4 rack width units with front panels 6.75"h X 3.75"w EF-404 equipment frame, quad unit rack mount for 1/4 rack width units with front panels 6.75"h X 3.75"w EF-501 equipment frame, single unit rack mount for 1/5 rack width units with front panels 5.0"h X 3.0"w EF-502 equipment frame, dual unit rack mount for 1/5 rack width units with front panels 5.0"h X 3.0"w EF-503 equipment frame, triple unit rack mount for 1/5 rack width units with front panels 5.0"h X 3.0"w EF-504 equipment frame, quad unit rack mount for 1/5 rack width units with front panels 5.0"h X 3.0"w EF-505 equipment frame, five unit rack mount for 1/5 rack width units with front panels 5.0"h X 3.0"w EF-506B equipment frame, rack mount for 440 series receivers EF-602 equipment frame for RS-112 receiving system FC-103 3 ch. xtal controlled converter FT-101A IF to tape converter, 21.4mHz input, 750kHz center output, 6lbs FT-201A half rack unit of FT-101A FT-207 wideband IF to tape converter, 21.4mHz input, 2.15mHz center output, 300kHz or 4mHz BW output to recorder FT-210 IF-tape converter, 21.4mHz input, 1.075mHz output, data bandwidth of 150kHz-2mHz, half rack width FT-210E same as FT-210 except has equalizer for min group delay FT-222 narrowband IF to tape converter, 21.4mHz input, 20 or 200kHz center frequency output, 500kHz BW FT-4557 frequency translator, 455kHz input, staggers the IF outputs of up to six receivers between 580Khz and 1330kHz, 50kHz BW, cost $2900 (1965) HFM-8 antenna multicoupler, 2-30mHz, 75ohm impedance, 8 outputs, 10dB maximum noise figure, 8dB gain, quick change connector outputs on rear (like RCA video patch bays), 8lbs, cost $400 (1964) HFM-8-1 same specs as HFM-8 except connectors on front panel HFM-8-2 same specs as HFM-8 except BNC on front panel HFM-8-3 same specs as HFM-8 except BNC on rear panel HH-11 tuning head, 2-30mHz, for use with 205 series and 215 Pan-Man receivers, low intermod design, dual conversion, 67.8 and 21.4mHz IFs, max noise figure 15dB HH-11-1 tuning head, 0.9-30mHz, otherwise identical to HH-11 HPF-2 high pass filter accessory for HPM-8 series, attenuates below 2mHz IFC-162 frequency converter, 160mHz IF input, 21.4mHz output IFD4-300 dual wideband 21.4mHz IF demodulators IFD-5 demodulator plug-in for DM-4, AM/FM/CW, 5kHz bandwidth IFD-15 demodulator plug-in for DM-4, AM/FM/CW, 15kHz bandwidth IFD-50 demodulator plug-in for DM-4, AM/FM/CW, 50kHz bandwidth IFD-100 demodulator plug-in for DM-4, AM/FM/CW, 100kHz bandwidth IFD-103 demodulator, 21.4mHz input, BW=10/50/100/300mHz, provides AM and FM output and predetection IF output for recording IFD-200 demodulator plug-in for DM-4, AM/FM/CW, 200kHz bandwidth IFD-201 demodulator, 21.4mHz input, BW=10/50/300/1000kHz, provides AM and FM output and predetection IF output for recording, half rack width IFD-210 demodulator, 160mHz input, FM, BW=10/22mHz (8.5mHz video), component of TDS-100 system IFD-500 demodulator plug-in for DM-4, AM/FM/CW, 500kHz bandwidth IFD-1000 demodulator plug-in for DM-4, AM/FM/CW, 1mHz bandwidth IFD-2000 demodulator plug-in for DM-4, AM/FM/CW, 2mHz bandwidth IFD-4000 demodulator plug-in for DM-4, AM/FM/CW, 4mHz bandwidth IFD-8000 demodulator plug-in for DM-4, AM/FM/CW, 8mHz bandwidth LIF-107 Log IF demodulator, component of RS-112 receiving system MC-103 master control, component of RS-112 receiving system MD-50 autoscan motor tuning drive, adapts single tuner units to automatic tuning MD-100 same specs as MD-50 except designed for dual tuner units MD-104 same specs as MD-50 except designed for four tuner RS-111 MTF-100A microwave tuner frame, accepts two TH- series tuning heads, 160 and 21.4mHz outputs, AFC, AGC and DAFC inputs MTF-101 microwave tuner frame, slave to MTF-100A, adds space for two additional TH- series tuning heads MTF-102A microwave tuner frame, accepts one TH- series tuning head, 160 and 21.4mHz outputs, AFC, AGC and DAFC inputs MP-101 carrier level meter panel, read peak or average, 21.4mHz IF input, contains IF strip and AM detector MP-102 deviation and tuning meter panel, 21.4mHz IF input, contains IF strip and FM detector MPP-101 microwave pan preselector, contains four YIG preselectors for each of 1-2/2-4/8/8-12gHz, requires PS-103, component of RS-112 receiving system NS-101 noise silencer demodulator plug-in for DM-4, AM/CW, 2mHz pre-ANL BW, 15kHz overall BW, 2.75lbs, cost $800 (1965) PEC-401 portable equipment case, holds one 440 or 441 receiver, battery operation w/ built-in nicad charger, built-in speaker and whip antenna PR-101 preamplifier, 23dB gain, 4.5dB noise figure, component of TDS-100 system PS-103 power supply, component of RS-112 receiving system PTM-101 pan tuner module, contains mixers, LO and IF preamps, component of RS-112 receiving system RD-105 remote frequency display, for use with DRO-311 S-9203A speaker panel, half rack version of S-9903D S-9901A speaker panel, 2.5"x10" speaker, 600ohm, headphone jack, cost $75 (1965) S-9902A same as S-9901A except with 7 input selector switch cost $100 (1965) S-9903D amplified speaker panel, 2.5"x10" speaker, 5 watt audio amp, 10k input impedance, 7 input selector switch, headphone jack, cost $160 (1965) S-9908B same specs as S-9903D except with eighth input position for microphone and BNC monitor output, cost $225 (1965) SFM-1 standard frequency multiplier, 1mHz standard input, 50/100/500/1000mHz output, 1vrms output SOR-1A signal operated relay, controls up to two devices with contact closure on voice, positive-going or negative- going DC, self-contained 6"w X 3.5"h X 7.75"d SP-101 storage panel for modules used with DM-4, cost $125 (1965) SWP-101 RF/IF switch panel, 3 inputs, 4 outputs, used in RS-125 SWP-104 RF/IF switch panel, 4 inputs, 4 outputs, used in RS-125 SWP-602 IF switch panel, 6 position, used with SDU to monitor several receivers, 1/2 rack width unit TDM-101 demodulator, 60-108kHz, SSB, twelve outputs 300-3500Hz, component of TDS-100 TDM-102 demodulator, 12-60kHz, SSB, twelve outputs 300-3500Hz, component of TDS-100 TDM-110 demodulator, ten 60-108kHz inputs, SSB, ten outputs 300- 3500Hz, component of TDS-100 TF-101 Tape to IF converter, converts tape recorder output centered at 750kHz into standard 21.4mHz TF-102 similar to TF-101 except with adjustable output freq TF-103 tape to IF converter, converts video signals in 40kHz to 4mHz range to 21.4mHz IF output, companion to IFD-103 TF-201 half rack unit of TF-101 TF-202 half rack version of TF-102 TF-210 tape to IF converter, 1.075mHz input center frequency, 21.4mHz output, digital thumbwell frequency control TFC-101 converter, 60kHz-4mHz input, twelve outputs in 312-552kHz range (CCITT supergroups 1-10), component of TDS-100 system TFC-105 converter, 2548-4028kHz input, six outputs in 312-552kHz range (CCITT supergroups 11-16), component of TDS-100 system TFC-212 converter, 312-552kHz input, five 60-108kHz outputs, component of TDS-100 system TH-120 1-2gHz drop-in tuner for 112 receiver and MTF-series microwave tuning frames, filmstrip dial, 11dB max noise figure, four section YIG preselector, 160mHz IF out, BW=22mHz @ -3dB, 3.15"h x 7.75"w x 14.9"d, 8lbs TH-120R-5 wideband version of TH-120, 50mHz @ -3dB, otherwise same TH-145R 1-4.5gHz, 16dB noise figure, 4 digit LED readout, electronically tuned, otherwise same as TH-120 TH-240 2-4gHz, 18dB max noise figure, otherwise same as TH-120 TH-245 2-4.5gHz, 20dB max noise figure, otherwise same as TH-120 TH-245R-5 wideband version of TH-245, 50mHz @ -3dB, otherwise same TH-480 4-8gHz, otherwise same as TH-240 TH-480R-5 wideband version of TH-480, 50mHz @ -3dB, otherwise same TH-812 8-12gHz, otherwise same as TH-240 TH-812R-5 wideband version of TH-812, 50mHz @ -3dB, otherwise same TH-1218R 12-18gHz, BW=50mHz @ -3dB, otherwise same as TH-240 TSU-103B tuner switching unit, works with 205, 205-2 or 215 Pan-Man receivers, manual selection of tuners, holds up to 3 tuners, part of RS-160, see RS-160 for details TSU-160 tuner switching unit, works with 205, 205-2 or 215 Pan-Man receivers, manual selection of tuners, holds up to 7 tuners, part of RS-160, see RS-160 for details UH-11 plug-in tuner, 250-500mHz, for 205, 205-2 or 215 receivers UH-12 plug-in tuner, 0.5-1gHz, for 205, 205-2 or 215 receivers UH-13 plug-in tuner, 220-440mHz, for 205, 205-2 or 215 receivers UH-101 plug-in tuner for 565 series receivers, 235-500mHz UH-102 plug-in tuner for 565 series receivers, 500-1000mHz UH-104 plug-in tuner for 565 series receivers, 490-1000mHz VDA-4 video distribution amplifier, four outputs, up to 20dB gain, meters four each output, 75ohm impedance, 1.5mHz bandwidth VH-11 plug-in tuner, 30-60mHz, for 205, 205-2 or 215 receivers VH-12 plug-in tuner, 60-120mHz, for 205, 205-2 or 215 receivers VH-13 plug-in tuner, 100-180mHz, for 205, 205-2 or 215 receivers VH-14 plug-in tuner, 180-300mHz, for 205, 205-2 or 215 receivers VH-15 plug-in tuner, 20-40mHz, for 205, 205-2 or 215 receivers VH-16 plug-in tuner, 40-80mHz, for 205, 205-2 or 215 receivers VH-17 plug-in tuner, 50-100mHz, for 205, 205-2 or 215 receivers VH-101 plug-in tuner for 565 series receivers, 20-90mHz VH-103 plug-in tuner for 565 series receivers, 90-260mHz VH-105 plug-in tuner for 565 series receivers, 200-425mHz VH-107 plug-in tuner for 565 series receivers, 100-400mHz VOR-1A voice operated relay, single channel unit, half rack VOR-2 voice operated relay, twelve channel unit, audio or COR detection, recorder interface for end of tape indication, rack mount 5.25" high, modular VOR-6 voice operated relay, 6 channel unit, individual delay and threshold controls, 20lbs, cost $815 (1964) WJ-1234 System interface unit, multi-functional, microprocessor- based operator/receiver interface, flexible command structure, 48 programmable scan strategies, 3000 emitter mode library file, 500mHz instantaneous bandwidth display. WJ-8610A Multiple receiver system control hub, up to 14 receivers and a variety of survelliance equipment, software program- mable, can be remote controlled by computer WJ-8971A DF processor, interfaces with 21.4mHz wideband IF output, usable with receivers from 20mHz to 1gHz, pseudo-doppler operation using synchronised antenna commutation and signal handling circuitry, LED compass rosette and three digit LED bearing readout, IEEE-488 controllable, 3 degree accuracy, selectable integration times, requires special antenna: WJ-9872A, WJ-9880(-1), WJ-9871A or WJ-9873, rack mount 5.25" high WJ-8971A mobile DF antenna for use with WJ-8971A or WJ-8975A, 20-235mHz and 150-1000mHz WJ-8971A-5 DF processor, same as WJ-8971A except with multiple IF BWs, bearing offset correction and remote control of IF BWs and integration times WJ-8971A-6 DF processor, same as WJ-8971A-5 except all functions are remote controllable through an IEEE-488 interface WJ-8971A-7 DF processor, same as WJ-8971A except with IEEE-488 remote control interface WJ-8971/AS DF antenna simulator, for alignment of WJ-8971A system WJ-8972A fixed site DF antenna for use with WJ-8971A or WJ-8975A, 20-150mHz and 150-1000mHz WJ-8973 ruggidized DF antenna for use with WJ-8971A or WJ-8975A, 20-235mHz and 150-1000mHz WJ-8975A manpack DF processor, line of bearing information for signals in the 20-500mHz range, LED compass rosette and three digit LED bearing readout, battery powered (internal 10 D cell or magnesium BA-4386 pack) or vehicular supply, used with WJ8640-1 receiver, (mil C-11495/PRD-11) WJ-8986/AU-3 DF antenna system, consists of 3,4 or 5 vertically polarized 15' monopoles spaced 14' apart, 2-30mHz, can be used with WJ-8986 with WJ-8986/AAU-1 option WJ-8986/AU-5 triple interferometer DF antenna bay, 20-1200mHz, ruggedized, 12.7'h, 75lbs WJ-8992 UHF psuedo doppler DF antenna, 500-1000mHz, used w/WJ-8990 WJ-9061 tuning head, drop-in, 20-90mHz, used in WJ-8730 series WJ-9062 tuning head, drop-in, 90-300mHz, used in WJ-8730 series WJ-9063 tuning head, drop-in, 200-425mHz, used in WJ-8730 series WJ-9064 tuning head, drop-in, 250-500mHz, used in WJ-8730 series WJ-9066 tuning head, drop-in, 30-90mHz, used in WJ-8730 series WJ-9068 tuning head, drop-in, 490-1000mHz, used in WJ-8730 series WJ-9150 tuner series, five units covering 1-18gHz, for use with the WJ-9450 demodulator/control unit WJ-9203A speaker panel, 7 audio inputs, high-Z in, 5W output, half rack 3.5" high WJ-9222 1.75" high version of FT-210 WJ-9222E 1.75" high version of FT-210E WJ-9240 1.75" high version of IFC-162 WJ-9290 microwave block downconverter, extends WJ-8609A-1 miniceptor to microwave range, tailored to specific communication bands, 10-14VDC, 4W, 0.75"h x 3.5"w x 6.0"d, 15oz WJ-9310 antenna multicoupler, twelve outputs, 20-1000mHz, 2dB gain, noise figure: 6.5dB (20-300mHz; 8.5dB (300-1000mHz), used in RS-180 system WJ-9311 antenna multicoupler, twelve outputs, 0.5-30mHz, 2dB gain, max noise figure 7dB WJ-9314 antenna multicoupler, four outputs, 20-1100mHz WJ-9315 antenna multicoupler, twelve outputs, 20-1100mHz, multiple antenna inputs WJ-9395 tunable demod, 1-900kHz, AM/FM/SSB, five digit LED readout, DAFC, BWs: 2/4/8/16kHz (AM/FM); 1/2/4/6kHz (USB/LSB), portable packaging 10"w x 12"d x 4"h WJ-9424 voice grade channel demodulator, up to 30 demods in single half rack case, demodulates VFT, modem & FAX voice grade signals, upgradeable through firmware, 3.5"h x 8.25"w x 22"d, 20lbs WJ-9450 demodulator/control unit, 160mHz IF input, AM/FM/pulse, 5 digit LED frequency display, 3 independent IFDs w/ 6 BWs per IFD, AFC, works with WJ-9150 series tuners WJ-9470 FSK/OOK demod system, handoff version of WJ-9472 WJ-9471 VFT FSK demodulator system, up to 24 independent demods, 200Hz-9.999kHz, phase-locked-loop demodulation, built-in diversity operation WJ-9472 two channel FSK demodulator system, FSK or OOK, digital control to 1Hz of mark and space frequencies from 200-9999 kHz, multipole matched baud rate filters for 10-4000 baud WJ-9477 precision tunable demodulator, AM/FM/SSB, 0.001-30mHz, 10Hz steps, provision for 9 BW filters (3kHz to 5Mhz), microprocessor controlled WJ-9477(G) tunable demodulator, AM/FM (SSB opt), 0-31mHz, 10Hz steps, provision for 9 BW filters (3.2kHz-6mHz), microprocessor controlled, 3.5"h x 8.5"w x 21"d, 20lbs WJ-9480 tunable demodulator system, consists of 2 units; tuner/IF amp and demod, 0.1-30mHz, 100Hz steps, simultaneous AM/FM/PM detection, 13 IF BWs (3kHz-20mHz), IEEE-488 remote, 21.4 & 160mHz inputs, 21.4/70/160mHz outputs, each section is 5.25"h x 19"w x 22"d, tuner: 44lbs, demod: 54lbs WJ-9497 tunable demodulator, 0-90mHz or 160mHz IF, 1Hz steps, AM/FM/SSB, programmable bandwidth from 100Hz-20mHz, BITE, 3.5"h x 8.5"w x 21"d, 20lbs WJ-9518A FDM demodulator, six independent SSB demodulators tunable from 0-15mHz, local or IEEE-488 control, preprogrammed tuning for standard CCITT 960 or 2700 channels, scanning available in increments of 1kHz to 1mHz or discrete frequency tuning. WJ-9518AE same as WJ-9518A except with delay equalized demodulators WJ-9525 FDM demodulator, consists of four /DU demodulator units, one /CU control unit and one /CRF controller rack frame WJ-9548 digital FDM demultiplexer, up to 24 tunable FDM channel demods in a single half rack case, channels tune 0-20mHz in 1Hz steps, 4 analog baseband inputs, 8 line by 40 char LCD display, 3.5"h x 8.25"w x 20"d, 20lbs WJ-9605 receiver front panel, provides local control for 1 or 2 WJ-8607 miniceptors, or remote control of WJ-8700 receiver, 3.5"h x 8.3"w x 3.1"d, 2.2lbs WJ-9607 multi-receiver front panel, provides for local control of up to 29 HPIL interfaced WJ-8607s, WJ-8609s or WJ-8809s, 3.5"h x 8.3"w x 4.4"d, 3.0lbs WJ-9644A receiver controller, can operate up to 32 WJ-8718 receivers through RS-232 interface WJ-9773-1 voice operated relay, two channels, rack mount 1.75" high WJ-9773-2 voice operated relay, four channels, rack mount 1.75" high WJ-9880 DF antenna, manpack, for use with WJ-8971A or WJ-8975A, 20-175mHz WJ-9880-1 DF antenna, manpack, for use with WJ-8971A or WJ-8975A, 20-175mHz and 150-850mHz WJ-9881 DF antenna, 20-512mHz, used w/WJ-8990 system WJ-9886-1 DF antenna, 20-1000mHz, 2 bays of vertically polarized elements, used w/WJ-8986 system WJ-9886-1A DF antenna, 20-2000mHz, 3 bays of vertically polarized elements, used w/WJ-8986 system WJ-9886-2 DF antenna, 20-1200mHz, similar to WJ-9886-1 except in a smaller package, used w/WJ-8986 system WJ-9902 equipment frame, houses 1 or 2 WJ-8706 or WJ-8609A miniceptors, intergral AC supply, optional host interface, can be fitted with WJ-9605 front panel, 3.5"h x 8.5"w x 20"d, 10lbs WJ-9903E speaker panel, 7 audio inputs, high-Z in, 5W output, full rack 3.5" high WJ-9908 equipment frame, houses up to 8 WJ-8706 or 8709A miniceptors, integral AC supply, optional host interface, 8.75"h x 19"w x 21"d, 20lbs WJ-9930-10 IF amplifier w/ 10kHz BW and limiter discriminator, used in WJ-9028, WJ-8730 series and 565A WJ-9930-20 same as WJ-9930-10 except 20kHz BW WJ-9930-50 same as WJ-9930-10 except 50kHz BW WJ-9930-100 same as WJ-9930-10 except 100kHz BW WJ-9930-200 same as WJ-9930-10 except 200kHz BW WJ-9930-300 same as WJ-9930-10 except 300kHz BW WJ-9930-500 same as WJ-9930-10 except 500kHz BW WJ-9930-1M same as WJ-9930-10 except 1mHz BW WJ-9930-2M same as WJ-9930-10 except 2mHz BW WJ-9930-3M same as WJ-9930-10 except 3mHz BW WJ-9948 blower module, for cooling a rack, 3,6 or 9 blowers, rack mount 1.75" high WJ-9949 speaker panel, five input, 1 watt output, half rack WJ-9950 speaker panel, on/off switch, unamplified WJ-9951 equipment frame, similar to EF-201 Systems: Model Description -------- ----------------------------------------------------------- AN/PRD-11 VHF/UHF radio DF system, 20-512 mHz, consists of WJ8640-1 receiver, WJ8975A DF processor, WJ-9180-1 SDU and WJ9880A antenna AN/TLQ-504 communications jamming system, military version of WJ-4810 RS-112 microwave Pan-Man receiving system, continuous four band simultaneous scanning of 1-12gHz, components may include: MPP-101 microwave pan preselector, PTM-101 pan tuner module, PS-103 power supply, LIF-107 log IF demod, MC-103 master control, PD-602 pan display, EF-602 equipment frame, PD-102 pan display, PD-201 pan display, MT-112 microwave tuner, DM-112 demod, 112 microwave receiver, SM1622 SDU RS-125 receiving system, coverage of 10-2000mHz available with four demodulators provide bandwidths ranging from 5kHz to 8mHz, basic system consists of SM-9401A, UT-1000C, VT-30C, SWP-104, DM-4C and S-9901, versatile sytem available in many configurations with no specialized components RS-158 receiving system, allows simultaneous monitoring of up to 12 channels in 20-80mHz range using 410 series plug-in receivers, basic components include 410 receiver, DRO-270 counter and EF-158 equipment frame containing multicoupler and RF test signal generator RS-160 Pan-Man receiving system, allows full band or sector scanning (pan/sector and remote with 205-2 or 215 receiver), basic single band configuration consists of 205 receiver, DRO-308 counter and SM-7301 SDU, uses HH-xx, VH-xx and UH-xx series tuning heads for 2-1000gHz coverage, DRX-308 frequency extender required for digital readout of UH- series tuners, TSU-160 tuner switching unit expands capacity to manual selection of up to 7 tuners, CSU-160 tuner switching unit permits sequential scanning (autostep) of up to 7 tuners, TSU-103B is similar to CSU-160 except it can only hold three tuning heads, additional options include VM-101, UM-101 and UM-160 marker generators, FS-101 2-300mHz synthesizer, FS-102 2-1000mHz synthesizer and EF-160 equipment cabinet, later versions of the system include 205-2 receiver which adds pan/sector and remote scanning or 215 receiver which adds TTL digital control and the DRO-335 counter which counts to 1gHz w/o an extender RS-168 EMC version of RS-180, other specs unknown RS-180 receiving system, AM/FM (CW opt), 30-1000mHz with 480 series tuners, components include DRO-280A counter, WJ-9310 multicoupler and EF-180A equipment frame for up to six 480 series rcvrs or EF-182A for up to 12 rcvrs, receivers time share the counter and DAFC functions, all receivers can monitor from a single broadband antenna TDS-110 carrier demultiplexing system, for microwave telephone signals in the 3.7-4.2gHz, 960 channels in 16 CCITT super- groups, consists of FE-3442 tuner, IFD-210 IF-tape demod, SM-1622 SDU, TFC-101 supergourp converter, TFC-105 super- group converter, TFC-212 basic supergroup converter, TDM-101 basic group demod, TDM-110 basic group demod, PR-101 LNA, ANT-101 antenna, APR-101 antenna/preamp WJ-1007 microwave collection system, 1-18gHz, surveillance set for detection and categorization emission parameters, computer controlled WJ-1026 electronically swept receiving system, 1-18gHz, ruggidized and remote controlled (up to 550 feet) for airborne or shipboard applications WJ-1047 dual channel receiving system, 0.5-12gHz, digitally tuned system designed for airborne DF and ELINT operation WJ-1088 airborne receiving system, 0.4-17.5gHz, designed for antenna pattern analysis, all data recorded digitally WJ-1140 modular microwave receiving system, 0.5-18gHz, extremely ruggdized compact system for ECM, ELINT, surveillance, tracking and broadband communications, digitally controlled WJ-1154 frequency synthesizer, 1-12.4gHz in 1mHz steps, BCD controllable by appropriate WJ receiver WJ-1920 Multi-parameter distributed processing system, dual reception using wide-band IFM receiver and a narrow-band superhetrodyne receiver design creates high probability of signal intercept, frequency-domain and time-domain processing of signals. WJ-4810 communications jammer, 2-500mHz, amplifier modules from 20-1000w available, single, multiple and barrage jamming modes, microprocessor controlled. WJ-8737 receiving system, very similar to WJ-9028 WJ-8940 receiving system, 5kHz-1gHz, (20Hz-18gHz opt), AM/FM/CW and log detection, 17 IF BWS from 200Hz-50mHz (5Hz w/ ELF opt), for EMC, EMI, Tempest and wideband RF ambient signal surveys, similar configuration to newer WJ-9040 WJ-8955 mobile ESM system, signal monitoring and netted direction finding capability over 2-1100mHz range, complete system consists of 3 vehicles, roof mounted DF antenna requires minimal deployment for set-up. WJ-8965A communications reconnaissance system, rapid detection of HF/VHF/UHF signals, unit will automatically determine line- of-bearing to VHF/UHF target transmitters, housed in transportable shelter or tactical vehicle, complete with antennas and masts. WJ-8976 three channel DF system, provides azimuth and elevation bearing information for many types of signals, monopulse, continuous and spread-spectrum, consists of three channel slave receiver, digital processor, master tuner and antenna system, basic operation from 20-500mHz, operation from 2mHz to 1.2gHz is also possible. WJ-8986 correlative vector 3-5 channel DF ssytem, 2-512mHz range, (expandable to 2gHz), 50mHz/sec scan and DF rate, PC/AT design, graphical front panel displays including spectrum FFT, 8.75"h x 19"w x 20"d, 66lbs WJ-8990 manpack tactical intelligence system (MANTIS), WJ8972 receiver/DF processor and WJ9881 antenna, RF intercept and DF capability over 20-500mHz range, can be expanded for intercept use from 0.5-1200mHz and DF coverage 2-1200mHz, manual or automated control of serach and DF operations, DF accuracy of 2 degrees, RS-232 controllable, 12VDC internal batteries or 24VDC vehicular power (120VAC opt), WJ8972: 6" X 11" X 16", 24lbs, WJ9881 (stowed) 14" X 14" X 35", 29lbs WJ-8991 manportable correlative vector DF system, consists of WJ-8996 DF processor, WJ-8997 covert/portable DF antenna, handheld controller, and optional handheld antenna for on-the-move operation, 1-1300mHz (2gHz opt), entire system fits into an ALICE pack, 19"h x 22"w x 12"d, 50lbs WJ-8996 correlative vector DF, 2 or 4 channel, 1-2000mHz, ruggidized, lower power consumption (10w) for covert/field deployment, options include RS-232 or ethernet interface and quick reaction analysis scan (100mHz/sec) WJ-8999 portable EMC/Tempest test receiver, 1kHz-1gHz coverage (1-12.4gHz opt), AM/FM/CW/Log, operating modes: fixed, scan/plot, scan/monitor, or remote, 18 IF BWs 100Hz-50mHz (100/200mHz opt), optional built-in signal monitor, designed for EMC, wideband ambient RF surveys, signal analysis, 7"h x 16.87"w x 15"d, 42lbs WJ-9023C wide range receiving system, 30mHz-12.4gHz, high resolution digital tuning, local or remote control, basic ssytem: WJ-9023C/TSU tuner sythesizer unit, WJ-9023C/IFD IF demod, WJ-9023C/DCU digital control unit and WJ-9023C/ICU interface control unit WJ-9028 receiving system, 20-1000mHz, AM/FM/CW/pulse, consists of two units, WJ-9028/RU receiving unit and WJ-9028/DU display unit, RU contains four tuners, COR, AFC, DAFC and provisions for up to 3 WJ-9930 IF amp/demod modules (10 BWs), DU contains counter and SDU, complete system is rack mount 5.25" high WJ-9040B receiving system, 5kHz-23gHz, multipurpose system for RFI/ EMI compatibility investigations, wide-band surveillance and narrow-band analysis. Composed of digital control unit (DCU), tune/synthesizer unit (TSU), IF demodulator (IFD) and auxiliary synthesizer unit (ASU), TSUs provide coverage from 5kHz-1gHz (20Hz-23gHz opt), resolution 1Hz across the range, 11 fixed-tuned and varactor-tuned pre- selection bandpass filters, autoranging antenna attenuator, IFDs provide bandwidths ranging from 200Hz-50mHz centered on 100kHz, 21.4mHz & 160mHz, Operator interface consists of 32 key keyboard, tuning wheel, analog controls for audio and IF gain, 256 character LCD alphanumeric display WJ-9045 modular tactical receiving system, 5kHz-440mHz using a series of receivers, digital control, DF capable WJ-9088 frequency management system, signal collection, measurement, modulation identification, sorting and management of signals from 10kHz to 1gHz in 10Hz steps, AM/FM/FM phase/CW/OOK/LSB/ USB and noise, tuning time of 20-250mS, controlled by PDP-11 computer which can record, sort and edit up to 30,000 signals via color monitor and function keys. WJ-9103 multichannel digital tuner, consists of up to 8 WJ-9103/DTM digital tuner modules, tunable LOs, equalization signal source, digital controller and support circuitry, 20-500mHz (20-2000mHz w/ extender opt), 2mHz instantaneous bandwidth (4mHz opt), for precision DF, spectral analysis, antenna beamforming, 5.25"h x 19"w x 22"d, 55lbs WJ-9104 multichannel digital tuner, similar to WJ-9103 except 20-2400mHz range for each channel, 10mHz instantaneous bandwidth, options include LF/HF capability (0-33mHz), programmable IF BWs (4kHz-10mHz), serial/fiber optic data output, ethernet or high-speed serial control interface, 20mHz instantaneous BW WJ-9195C rapid acquisition spectrum processor (RASP), broadband receiver and spectrum display device, 20-512mHz (expandable 2mHz to 4gHz), 1gHz per second scan rate (!!!), 5 or 25kHz resolution, electroluminescent display, six programmable traces, manual or remote computer control, Can act as a system controller for up to 15 WJ904 receivers, rack mount 8.75" high, 89lbs. WJ-32320 ELINT/ESM system, 0.5-18gHz, tells you everything you want to know about every kind of emitter in the area including its location as determined by triangulation and GPS. Not for mere mortals. Contibutors include Tom Adams, Bob Folwaczny, Geoff Greer, Dennis Karski, Emil Kasprzyk, Charlie Mylod, Terry O'Laughlin, and Tony Snider Edited by Terry O'Laughlin, WB9GVB Additions, corrections, suggestions to: e-mail: olaughlin@vilas.uwex.edu snail-mail: P.O. Box 3461, Madison, WI 53704-0461 landline: 608-244-3135